机器特性：

1. 本机设计原理采用全油压左右双工位动作构造，压制成型鞋，和组底加工两用压合，360°***强力触压，无需压底模和侧模，两机一人操作，压力稳定、精准、无波动偏差、受力均衡减少边墙边角脱胶率，压力大小可根据制鞋形体需求0-40KG压力任意调节，制鞋常均使用压力20-35KG。压著时间均6-12S或根据鞋型需求时间调节
   
2. 适用鞋型常规运动慢跑鞋、注塑胶钉足球鞋、注塑胶钉棒球鞋、中帮鞋、和材质、网布、皮革、PU皮、帆布鞋等
   
3. 此机压放鞋胶模水缸规格尺寸395*160*230MM，可压制成品鞋***码数US18-19码、UK18码、EUR51.5码、39CM，高度230MM。可压制成品鞋***小码数US3.5码、UK2.5码、EUR37码、CM21.5或无限制、使用上平模压制的一工位可压制儿童小码鞋一次一双
   
4. 鞋底及边墙接触的下水缸胶模软囊材质（橡胶）厚度5-8MM、硬度35-55℃、两种硬度材质、采用日本特种胶料材质研制而成、有高弹拉力强度、生命周期、注塑胶钉足球鞋底保固期11万次、常规运动慢跑鞋底保固期11万-22万次、55℃材质或更多（鞋子放置方法：侧放X一倒放X一正放√）
   
5. 下水袋使用转换配项：组底压合搭配使用水带深度80MM***效果和***率速度
   
6. 成品鞋：鞋底与楦头总高度110-160MM搭配使用水带深度110MM、因为机器正常工作时上模下压合并时、上模需要压盖住楦头孔，以避免楦头孔强力吸破下水袋、和有过多的水袋挤破鞋面、每次压放鞋子时以后跟到位为标准、鞋底与楦头总高度160-230MM搭配使用水带深度140MM、因为下水袋有高弹强度拉伸力
   
7. 注意事项：请勿用单放空楦头或尖锐金属硬件液压
   
8. 机台工作原理：电路＋油路组合、油电控制、放置制鞋下缸注入专用水性油加压方式
   
9. 本机配置IE3二级能效马达、已通过Nike品牌授权的SGS公司做第三方安全CE认证书、装置防爆安全门、电眼传感器、急停开关、三重安全装置、杜绝安全隐患
   

Machine characteristics:

1. The design principle of this machine adopts a fully hydraulic left and right dual station action structure, which is used for pressing and forming shoes, as well as for sole processing. It has a 360 ° strong contact pressure in all directions, without the need for bottom and side molds. The two machines are operated by one person, with stable and accurate pressure, no fluctuation deviation, and balanced force, reducing the rate of wall and corner debonding. The pressure can be adjusted according to the shape requirements of the shoe making body, with a pressure of 0-40KG, and the shoe making usually uses a pressure of 20-35KG. The pressing time is 6-12 seconds or adjusted according to the shoe shape requirements
   
2. Suitable for regular sports jogging shoes, injection molded nail football shoes, injection molded nail baseball shoes, mid top shoes, and materials such as mesh, leather, PU leather, canvas shoes, etc
   
3. This machine can press shoe glue molds with a water cylinder size of 395 * 160 * 230MM. It can press finished shoes up to sizes US18-19, UK18, EUR51.5, 39CM, and has a height of 230MM. The optimal size for compressed finished shoes is US3.5, UK2.5, EUR37, CM21.5 or unlimited. One workstation with upper flat mold can press one pair of children's small shoes at a time
   
4. The soft bag material (rubber) of the water tank rubber mold in contact with the sole and side wall has a thickness of 5-8MM, a hardness of 35-55 ℃, two different hardness materials, developed using Japanese special rubber materials, high elastic and tensile strength, a life cycle, an injection molded rubber nail football sole warranty period of 110000 times, a regular sports jogging sole warranty period of 110000-220000 times, a 55 ℃ material or more (shoe placement method: side placement X inverted placement X one upright placement √)
   
5. Conversion configuration for the use of drainage bags: bottom pressing combination with a water hose depth of 80mm for optimal effect and high efficiency speed
   
6. Finished shoes: The total height of the sole and last is 110-160mm, and a water hose depth of 110mm is used in combination. When the machine is working normally, the upper mold needs to cover the last hole to avoid strong suction of the last hole and excessive water bags squeezing the shoe upper. The standard is to follow the shoes in place after each pressing. The total height of the sole and last is 160-230mm, and a water hose depth of 140mm is used in combination because the last hole has high elastic strength and tensile force
   
7. Attention: Do not use single empty last or sharp metal hardware hydraulic pressure
   
8. Working principle of the machine: circuit+oil circuit combination, oil and electricity control, placement of shoe making lower cylinder, injection of specialized water-based oil pressurization method
   
9. This machine is equipped with IE3 level 2 energy efficiency motor, SGS company authorized by Nike brand has obtained third-party safety CE certification, equipped with explosion-proof safety door, electric eye sensor, emergency stop switch, triple safety device, and eliminates safety hazards